Mikrotik RouterOS v7 beta

[BillyVan]

What's new in 7.18rc2 (2025-Feb-21 12:50):

*) cloud - added "Back To Home Files" feature (additional fixes);
*) dhcpv6-relay - added option to create routes for bindings passing through relay (additional fixes);
*) disk - do not allow adding device in raid when major settings mismatch in superblock and config;
*) disk - fixed removing device from raid while resyncing;
*) ethernet - fixed issue with default-names for RB4011, RB1100Dx4, RB800 devices (additional fixes);
*) ethernet - fixed link-down on startup for ARM64 devices (introduced in v7.16);
*) l3hw - added initial HW offloading for VXLAN on compatible switches (additional fixes);
*) lte - added initial eSIM management support (additional fixes);
*) lte - fix R11e-4G modem initialization (introduced in v7.18beta4);
*) lte - fixed cases where the MBIM dialer could get stuck;
*) lte - fixed interface recovery in mixed multiapn setup for MBIM modems (additional fixes);
*) lte - improved initialization for external USB modems;
*) ptp - improved system stability;
*) qos-hw - fixed wred-threshold (introduced in v7.18beta2);
*) ssh - improved channel resumption after rekey and eof handling;
*) wifi-qcom - prevent AP from transmitting broadcast data unencrypted during authentication of first client;
*) winbox - added missing options under "System/Disk" menu (additional fixes);

[deniSun]

[BillyVan]

Για τους δυνατους

7.20_ab26

https://box.mikrotik.com/d/c2fc960065ed49b78214/



Την περασα σε ενα 750gr3 να δω τιποτε καινουργιο απ το μελλον

[BillyVan]

What's new in 7.19beta2 (2025-Feb-28 08:58):

Spoiler:

*) arp - added warning, when "Published" ARP entry used on an interface with "reply-only" ARP mode enabled;
*) bgp - added input.filter-community;
*) bgp - fixed input.accept-community;
*) bgp - fixed memory leak on receiving notify and closing session;
*) bgp - improved performance on BGP input;
*) bonding - added setting for LACP active/passive modes;
*) bridge - added new STP monitoring fields for bridge and ports (Tx/Rx BPDU, Tx/Rx TC, forward/discard transitions, last topology change, message-age, max-age, remaining-hops, bridge-id);
*) bridge - fixed bridge port hang when using invalid port IDs;
*) bridge - fixed dhcp-snooping in QinQ setups;
*) bridge - fixed minor memory leak on link down;
*) bridge - fixed multicast packet flow on hardware offloaded bridge which acts as "multicast-router";
*) bridge - improved default bridge and port layout on console and GUI;
*) bridge - improved stability in case of configuration error (introduced in v7.15);
*) bridge - moved "TCHANGE" logs from bridge,stp to bridge,stp,debug;
*) bridge - rename "ports" to "interface" under MDB table for configuration consistency with other menus;
*) bridge - renamed STP monitor fields (port-number to port-id, designated-port-number to designated-port-id, designated-bridge to designated-bridge-id);
*) bridge - show designated-* monitor field for all port roles;
*) bridge - show warning instead of causing error when using multicast MAC as admin-mac (introduced in v7.17);
*) capsman - fixed "undo" command for cap interfaces;
*) certificate - added built-in root certificate authorities store;
*) certificate - do not include CA identity in SCEP POST requests;
*) certificate - improve error message when trying to use certificate;
*) certificate - optimize trust store;
*) cloud - changed asset CDN URL for "BTH Files";
*) cloud - fixed issues when BTH is toggled fast between enable/disable;
*) console - disallow incomplete double-quoted arguments (allows multiline string pasting);
*) console - fixed issue with files when using scripts (introduced in v7.18);
*) console - fixed misaligned multiline in brief print mode;
*) console - improved file add/remove process stability;
*) console - set "/system/note show-at-login=yes" the default value after configuration reset;
*) container - allow changing container name;
*) container - try to derive a user readable container name from remote image or file;
*) dhcpv4 - improved outgoing packet logging;
*) dhcpv4-server - accept packets with htype 6;
*) dhcpv4/v6-client - added check-gateway parameter;
*) dhcpv6-client - allow selecting to which routing tables add default route;
*) dhcpv6-relay - clear saved routes on DHCP release;
*) dhcpv6-relay - show client address;
*) dhcpv6-server - change bound status to waiting on binding disable;
*) dhcpv6-server - fix when expired static binding is declined with false "binding belogs to another server" reason;
*) dhcpv6-server - improved stability when disabling server with active bindings;
*) disk - add "sector-size" property in print detail;
*) disk - add reset-counters to /disk btrfs filesystem;
*) dlna - improved folder indexing behavior;
*) dns - improved DNS server service stability;
*) dot1x - fixed dynamic switch ACL rules on boards with a lot of ports (e.g. CRS520);
*) ethernet - improved Ethernet and PoE port mapping to ensure a consistent and reliable interface order;
*) file - improved responsiveness on slow filesystems;
*) firewall - always show "passthrough" when exporting mangle table;
*) firewall - detect VRF addresses as local;
*) health - hide settings in CLI if there is nothing to show;
*) health - improved performance on devices with simple voltage sensors;
*) igmp-proxy - do not try to send leave message for multicast groups that the device itself has joined on the upstream interface (cosmetic fix for proxy error logs);
*) iot - improvement to lora dev-addr-validation behavior;
*) iot - improvement to lora join eui/net id filtering behavior;
*) ip-service - show all TCP/UDP connections on the system;
*) ip-service - show all TCP/UDP ports on system, including ports in containers;
*) ip-service - show error message when service enable fails;
*) ipv6 - avoid watchdog reboot due to link-local IPv6 address reconfiguration on thousand of interfaces at once;
*) l2tp-ether - improved stability when trying to connect to disabled L2TP server with IPsec;
*) l3hw - remove VLAN tag before VXLAN encapsulation (fixes pvid behavior for bridged VXLAN);
*) log - added additional CEF fields from firewall and login logs;
*) log - populate in/out fields in firewall CEF logs with correct data;
*) lte - added UICC parameter in LTE monitor for R11e-4G modem;
*) lte - fixed modem recovery after firmware upgrade for R11e-LTE modem;
*) lte - fixed Router Advertisement processing issue for AT modems when an APN with "ip-type=ipv6" was configured;
*) lte - improved dialer for EC200A-EU modem;
*) lte - set apn profile name the same as apn if no name specified when creating the profile;
*) netinstall - improved network socket re-opening when NIC status changes while running the server;
*) netinstall - show warning when network configuration on PC might not be appropriate for installation;
*) netinstall-cli - fixed issue with applying the branding package;
*) ovpn - disable hardware accelerator for GCM on MMIPS CPUs (introduced in v7.18);
*) ovpn-server - do not reset active connections when changing comment or name;
*) pimsm - fixed issue where own query caused querier detection;
*) poe-out - upgraded firmware for 802.3at/bt PSE controlled boards (the update will cause brief power interruption to PoE-out interfaces);
*) ppc - fixed VLAN TCP packet transmit on PPC devices;
*) profiler - improved process classification;
*) ptp - added "ptp" logging topic;
*) quickset - improved system stability;
*) rose-storage - fixes for btrfs;
*) route - added options to set dynamic-in and connected-in chains in /routing/settings;
*) route - fixed stuck output when calling prints from multiple routing menus;
*) route - make AFI naming consistent;
*) route - show BGP session name instead of cache-id;
*) route-filter - improved performance;
*) sfp - added sfp-encoding data output from EEPROM;
*) sniffer - add max-packet-size (2k-64k) setting to be able to sniffer more than 2k data per packet;
*) ssh - fixed authorization with SSH key when multiple user SSH public keys are imported;
*) ssl/tls - respond with more precise alert error messages;
*) ssl/tls - send certificate authority in Certificate message even if it is not trusted;
*) switch - do not count rx-too-long multiple times on 100Gbps QSFP28;
*) switch - fixed egress mirroring for packets coming from external CPU port (e.g. CRS520, CCR2216, CCR2116);
*) switch - flush CPU port FDB entries on switch disable;
*) switch - improve rate limit accuracy for MT7531, MT7621, EN7562CT;
*) switch - improved boot stability on devices with Alpine CPU and switch chip;
*) switch - improved stability when enabling IGMP snooping with VXLAN (introduced in v7.18);
*) system - improved internal "flash/" prefix handling for different file path related settings;
*) webfig - allow table column resize over side toolbar;
*) webfig - don't reorder rows when selecting header cells with Alt+click;
*) webfig - show IPv6 firewall connections;
*) webfig - show missing data in "IP/DNS/Cache" records;
*) wifi - add channel.reselect-time parameter which allows to perform channel re-sellection at given time of day (CLI only);
*) wifi - add information on CAP uptime and connection uptime in "Remote CAP" list;
*) wifi - added "eap-identity" to registration table;
*) wifi - added SSID to logs;
*) wifi - fix authentication of clients which omit some RSN information at association;
*) wifi - fix incorrect info about current channel for station interfaces after AP has switched channel (introduced in v7.17);
*) wifi - re-word log entries about disconnections which are likely caused by peer using a wrong passphrase;
*) wifi - use at least TLS 1.2 for securing connection between CAPsMAN manager and CAPs;
*) wifi-qcom - fix inability of interfaces in station mode to connect if they do not support full bandwidth of AP;
*) winbox - added "MAC Telnet" under "Wifi/Registration" menu;
*) winbox - added "Multi Passphrase Group" for wifi;
*) winbox - added "Reset MAC address" for legacy wireless and wifi;
*) winbox - added country to wireless setup-repeater;
*) winbox - changed default wireless wds-cost-range values;
*) winbox - do not show not relevant values for certificate template;
*) winbox - fixed missing SMB client on non-ROSE devices;
*) winbox - fixed switch menu for Chateau 5G;
*) winbox - improve graphing efficiency when communicating with WinBox;
*) wireguard - add wg-import config-string parameter to import config directly from terminal;
*) wireguard - update peer info on "get" command;
*) wireless - added "eap-identity" to registration table;
*) wireless - implement handling of RADIUS disconnect messages by CAPsMAN;
*) wireless - suggest all legitimate frequencies for interfaces with 20/40mhz-XX channel width in GUI;
*) x86 - added support for Emulex NIC;

[deniSun]

[BillyVan]

What's new in 7.19beta4 (2025-Mar-06 14:10):

*) bridge - fixed dhcp-snooping in QinQ setups (additional fixes);
*) console - added on-error to "for" and "foreach" loops;
*) console - added proplist to monitor command;
*) console - do not treat return values as errors in scripts run from scheduler;
*) console - enabled verbose error logging for non-scripted/non-verbose imports;
*) console - improve time value handling;
*) console - validate script arguments (do, on-error, etc.) and reject invalid values;
*) dhcpv4-server - "Relay-Agent-Information" (82) option moved at the end of option list in response packets;
*) file - added show-hidden parameter to /file/print, allowing referencing and deleting hidden files;
*) hotspot - improvements to memory usage;
*) lte - additional fixes for eSIM management support;
*) lte - AT modems, improved redialing when modem lost connectivity without notifying host about APN status change;
*) lte - initial support for user settable modem redial timer;
*) netinstall - fixed issue with launching the app (introduced in v7.19beta2);
*) netinstall - provide warning if memory on installed router is full after installation;
*) ospf - fixed "mismatch" typo in logs;
*) port - added support for Huawei E3372-325 variant (vendor-id="0x3566" device-id="0x2001");
*) port - added USB mode switch support for "huawei-alt-mode";
*) port - improvements to KNOT BG77 modem port channel handling;
*) rose-storage - show btrfs balance and scrub errors if any;
*) torch - improved data reporting;
*) wifi - display error when trying to run snooper on interface which does not support wireless packet capture (sniffer);
*) wifi - fix possible snooper crash when parsing frames with malformed headers;
*) wifi - implement WPA2 PSK authentication with key derivation using SHA256 (CLI only);
*) wifi - improve parsing of captured frames which have nested flags in radiotap header;
*) wifi-qcom - fix OWE authentication for 802.11ac interfaces in station mode;
*) winbox - added comment under "User Manager/Routers" menu;
*) winbox - added netmask support for switch rule Src/Dst IPv6 Address settings;
*) winbox - fixed "Multi Passphrase Group" setting for wifi;
*) x86 - i40e updated driver to 2.27.8 version;

[deniSun]

[BillyVan]

Winbox

What's new in 4.0beta18:

*) User interface: small improvements
*) Table: when copying an object in an ordered list, the copied object is now placed immediately after the original
*) Login: do not accept IPv4 with zero prefixes in "Connect to" field
*) Form: do not accept IPv4 addresses format where numbers have zeros as prefix
*) Table: move total/selected/filtered count to left side of status bar
*) Form: validate min/max length of password fields
*) Fix crash when workspace restores window with different type (e.g., System->Health on routers vs x86/CHR)
*) Form: fix an issue where dynamically generated tabs (e.g., IGMP Snooping) did not properly show or hide their child elements
*) Table: hide/clip icons to cell width
*) Table: improve UI performance on initial table loading
*) Disable TCP Nagle algorithm
*) Fix read-only multi-checkbox field
*) Fix missing button in specific cases (e.g., System/Disks/BTRFS, LTE/eSIM)
*) Allow selecting text for read-only fields in some specific cases
*) macOS: set bundle version and GUI identifier values

[deniSun]

Αν δεν βγει stable και δεν καθοριστεί ως υποχρεωτικό
δεν θα το χρησιμοποιήσω.

[BillyVan]

Οσο κι αν εχω προσπαθησει για να το μαθω αντιμετωπιζω προβλημα.

Βασικα κανω παραπανω κινησεις απ οτι στο παλιο και αυτο με τα διπλωμενα μενου μου σπαει τα νευρα.

[macro]

Δε με βολευει οπτικα εμενα.

[BillyVan]

What's new in 7.19beta5 (2025-Mar-12 12:42):

*) certificate - added built-in root certificate authorities store (additional fixes);
*) console - fixed issue with file-name completion (introduced in v7.18);
*) container - fixed repository name handling to prevent redirect issues when basic authentication is used;
*) dhcpv4-client/server - added support for DHCPv4 reconfigure messages;
*) dhcpv6-server - change static binding bound status to waiting on server disable;
*) dhcpv6-server - improved stability when disabled server have static bindings;
*) firewall - fixed IP/Settings "ipv4-fasttrack-active" status showing as inactive when it is active;
*) queue - fixed system failure when CAKE kind queue was configured but queue type definition does not exist anymore (introduced in v7.18);
*) wifi - fixed incorrect attribution of 802.11be capability to 802.11ax APs in output of scan command (introduced in v7.19beta2);
*) wifi - fixed sending of reassociation response frames (introduced in v7.19beta2);
*) wifi - improved stability for wifi interfaces;

[deniSun]

[gaig]

Οσο κι αν εχω προσπαθησει για να το μαθω αντιμετωπιζω προβλημα.

Βασικα κανω παραπανω κινησεις απ οτι στο παλιο και αυτο με τα διπλωμενα μενου μου σπαει τα νευρα.

ακιβως το ιδιο, το ματι μου δεν μπορει να συνηθισει οτι εχουν ανοιγει ολα τα subtabs στο πλαι, νομιζω οτι δεν τα βρισκω ενω ειναι ολα εκει μπροστα

[BillyVan]

What's new in 7.19beta6 (2025-Mar-19 09:56):

*) bridge - fixed issue when local MACs were removed unnecessarily;
*) bridge - offload VXLAN only if another HW offloaded port exists in the bridge;
*) dhcp-server - improved stability when dual stack is used and one of the servers is removed (introduced in v7.19beta2);
*) dhcpv4/v6-client - fixed default route when DHCP client interface is in VRF;
*) dhcpv6-server - allow unsetting prefix-pool for static bindings and show warning if prefix is not in selected prefix-pool;
*) file - fixed missing files from The Dude (introduced in v7.18);
*) lte - Chateau 5G R16 fix DHCP relay packet forwarding using LTE interface;
*) net - remove support for automatic multicast tunneling (AMT) interface (introduced in v7.18);
*) netinstall-cli - clear old configuration before user script using "-s";
*) ovpn - properly match GCM hardware acceleration capabilities (introduced in v7.17);
*) route - improve stability on BGP reconnect;
*) x86 - remove unnecessary console output on shutdown;